+27 21 879 3034 info@linact.co.za
Caravan, Camper & Pop-Top Applications

Caravan Roof Lifts & Roof Lifters

For New Builds, OEM & Selected Retrofit Applications

Electric linear actuator systems for caravan, camper and lifting-roof applications. Standard multi-actuator and synchronous configurations are available in 12V and 24V, depending on the application requirements.

NEW BUILDS OEM MANUFACTURERS SELECTED RETROFITS
Discuss Your Application
Vertical actuator installation is preferred where the design and available space allow. Where an actuator must operate at an angle, the required actuator force must take the mounting geometry into account.
Electric linear actuators lifting a caravan pop-top roof vertically
Caravan roof lift application using electric linear actuators in a direct vertical lifting arrangement.
System Options

Standard or Synchronous?

Both approaches can work successfully. The choice depends on the roof design, stroke length and how evenly the load is distributed.

Simple & Proven

Standard Multi-Actuator Systems

Two or four standard actuators can be used where the roof is suitably balanced and independent actuator movement is acceptable.

Standard actuators do not travel at precisely identical speeds. Small speed differences are normal and can become more noticeable over longer strokes.

Typical configurations: 2 or 4 actuators
Coordinated Movement

Synchronous Systems

Synchronous control may be preferred where more coordinated movement between multiple lifting points is required.

  • Longer lifting strokes
  • Uneven roof loading
  • Air-conditioner concentrated on one area
  • Solar panels or other unevenly distributed equipment
Available as 2, 3 or 4 actuator sets
Real Applications

See Caravan Roof Lifts in Action

Real actuator-based roof lifting applications using different roof and installation layouts.

Caravan Roof Lift Application
Electric Roof Lifting in Action
Camper Roof Lift Application
Popular Actuator Range

LINACT-J Roof Lift Systems

A versatile 12V and 24V actuator range for many caravan roof lifting applications.

Standard & Synchronous Configurations

The LINACT-J can be used in standard multi-actuator installations or in synchronous sets where coordinated movement is preferred.

The most suitable configuration depends on the roof load, lifting direction, travel required and overall design of the system.

View LINACT-J
Specialised actuator options are also available.
Additional configurations can be supplied for suitable applications requiring enhanced environmental protection or manual emergency operation. Details are provided after the application has been reviewed.
Selection Guidance

Why the application matters

A caravan roof lift is not selected on roof weight alone. Stroke length, lifting direction, number of lifting points and load distribution all influence the actuator requirement.

Linear Actuators South Africa assists with actuator and control product selection based on the application information supplied.

What We Need

Information Required for Product Selection

These basic details help us narrow down a suitable actuator and control configuration.

Roof WeightKnown weight of the lifting roof.
Lift DirectionVertical lift or angled actuator installation.
Actuator Stroke Required (A)The actuator travel from fully retracted to fully extended. Do not use the overall gas strut length.
Number of ActuatorsExpected actuator quantity or lifting points.
Supply Voltage12V or 24V.
Force per ActuatorIf already calculated by the manufacturer or installer.
For a vertically lifting roof, roof weight is an important selection factor. Where an actuator operates at an angle or through another mechanism, the force required at the actuator can be considerably higher. The manufacturer, builder or installer remains responsible for determining the actual force required by the mechanism.
Existing Vehicles

Selected Retrofit Applications

Retrofit projects can often be considered where the required roof and actuator information is known.

Retrofit Example

When space limits a vertical installation

Existing caravan and camper layouts do not always provide enough space for actuators to operate vertically. In these cases an angled installation may be considered.

Where possible, a straighter lifting arrangement is preferred. With angled installations, the force required at the actuator must account for the mounting geometry.

Because existing roof mechanisms vary significantly, component selection is based on the information supplied by the customer or installer.

Installation Consideration

Weather Protection & Water Ingress

Roof lifting systems operate in an exposed environment, so the complete installation must be designed with water protection in mind.

Actuator Protection

The actuator IP rating applies to the actuator itself and does not make the complete roof lift installation waterproof.

Different actuator configurations are available for applications with different environmental requirements.

Complete Installation

The installer or manufacturer remains responsible for protecting wiring, connectors, controllers and mounting areas against rain, spray and water accumulation.

Water should not be allowed to collect around seals, electrical connections or control components.

Alternative OEM Solution

Looking for a Complete Lifting-Frame System?

For OEM and vehicle-manufacturer applications requiring a complete stabilised scissor-frame roof lifting mechanism, view our X-Frame Roof Lift System.

View X-Frame Roof Lift
X-Frame pop-up roof lift mechanism for camper and caravan applications
Common Questions

Frequently Asked Questions

Can you assist with an existing caravan?

Yes. Selected retrofit applications can be considered where the required specifications are known.

Do I need synchronous actuators?

Not necessarily. Standard systems can work successfully where the roof is suitably balanced and the design allows independent actuator movement.

Why can standard actuators move out of sync?

Individual motors naturally have small speed differences. These differences can become more noticeable over longer strokes or where loads differ between lifting points.

Is vertical lifting better than mounting the actuator at an angle?

Vertical or near-direct lifting is preferred where space and design allow. Angled installations can still work, but the required actuator force must account for the mounting geometry.

Are the actuators waterproof?

Different protection levels are available, but the complete installation must also be correctly protected against water ingress.

Do you install caravan roof lift systems?

No. We supply actuator, control and related components together with product-selection support. Integration and installation remain the responsibility of the builder or installer.

Important Measurement

Which Measurement Do We Need?

For actuator selection, we require the stroke length only. Please use Measurement A in the image below.

Actuator measurements showing A retracted length, B stroke length and C extended length
A = Stroke — THIS IS WHAT WE NEED
The distance the actuator rod travels from fully retracted to fully extended.
B = Retracted Length
Overall actuator length when fully closed.
C = Extended Length
Overall actuator length when fully extended.
Please enter Measurement A only in the enquiry form.
Do not enter the overall length of the existing gas strut, the closed length, or the fully extended overall length. The actuator stroke is the actual travel distance.
Enquiries

Discuss Your Caravan Roof Lift Application

Complete the known application details below, then send the enquiry directly to us by WhatsApp or email. We can assist with actuator and control product selection based on the information supplied.

Enter Measurement A only. Do not enter the overall gas strut length.
* Name, email, phone / WhatsApp and actuator stroke (Measurement A) are required. Component selection is based on the information supplied. Mechanical design, installation and engineering of the roof structure remain the responsibility of the manufacturer, builder or installer.